onewire for esp32 improved, retry for sensors

lib/OneWire/OneWire.cpp

@@ -161,7 +161,11 @@ void OneWire::begin(uint8_t pin) {
 //
 // Returns 1 if a device asserted a presence pulse, 0 otherwise.
 //
+#ifdef ARDUINO_ARCH_ESP32
+uint8_t IRAM_ATTR OneWire::reset(void) {
+#else
 uint8_t OneWire::reset(void) {
+#endif
     IO_REG_TYPE mask           IO_REG_MASK_ATTR = bitmask;
     volatile IO_REG_TYPE * reg IO_REG_BASE_ATTR = baseReg;
     uint8_t                    r;
@@ -195,7 +199,11 @@ uint8_t OneWire::reset(void) {
 // Write a bit. Port and bit is used to cut lookup time and provide
 // more certain timing.
 //
+#ifdef ARDUINO_ARCH_ESP32
+void IRAM_ATTR OneWire::write_bit(uint8_t v) {
+#else
 void OneWire::write_bit(uint8_t v) {
+#endif
     IO_REG_TYPE mask           IO_REG_MASK_ATTR = bitmask;
     volatile IO_REG_TYPE * reg IO_REG_BASE_ATTR = baseReg;
 
@@ -222,7 +230,11 @@ void OneWire::write_bit(uint8_t v) {
 // Read a bit. Port and bit is used to cut lookup time and provide
 // more certain timing.
 //
+#ifdef ARDUINO_ARCH_ESP32
+uint8_t IRAM_ATTR OneWire::read_bit(void) {
+#else
 uint8_t OneWire::read_bit(void) {
+#endif
     IO_REG_TYPE mask           IO_REG_MASK_ATTR = bitmask;
     volatile IO_REG_TYPE * reg IO_REG_BASE_ATTR = baseReg;
     uint8_t                    r;
@@ -473,6 +485,7 @@ bool OneWire::search(uint8_t * newAddr, bool search_mode /* = true */) {
         for (int i = 0; i < 8; i++)
             newAddr[i] = ROM_NO[i];
     }
+    // depower(); // https://github.com/PaulStoffregen/OneWire/pull/80
     return search_result;
 }
 

lib/OneWire/OneWire.h

@@ -78,7 +78,11 @@ class OneWire {
     // Perform a 1-Wire reset cycle. Returns 1 if a device responds
     // with a presence pulse.  Returns 0 if there is no device or the
     // bus is shorted or otherwise held low for more than 250uS
+#ifdef ARDUINO_ARCH_ESP32
+    uint8_t IRAM_ATTR reset(void);
+#else
     uint8_t reset(void);
+#endif
 
     // Issue a 1-Wire rom select command, you do the reset first.
     void select(const uint8_t rom[8]);
@@ -101,11 +105,18 @@ class OneWire {
 
     // Write a bit. The bus is always left powered at the end, see
     // note in write() about that.
+ #ifdef ARDUINO_ARCH_ESP32
+   void IRAM_ATTR write_bit(uint8_t v);
+ #else
    void write_bit(uint8_t v);
+#endif
 
     // Read a bit.
+#ifdef ARDUINO_ARCH_ESP32
+    uint8_t IRAM_ATTR read_bit(void);
+#else
     uint8_t read_bit(void);
-
+#endif
     // Stop forcing power onto the bus. You only need to do this if
     // you used the 'power' flag to write() or used a write_bit() call
     // and aren't about to do another read or write. You would rather

src/sensors.cpp

@@ -72,7 +72,6 @@ void Sensors::loop() {
                 YIELD;
                 bus_.skip();
                 bus_.write(CMD_CONVERT_TEMP);
-
                 state_ = State::READING;
             } else {
                 // no sensors found
@@ -86,20 +85,15 @@ void Sensors::loop() {
             // LOG_DEBUG(F("Scanning for sensors")); // uncomment for debug
             bus_.reset_search();
             found_.clear();
-
             state_ = State::SCANNING;
-            last_activity_ = time_now;
         } else if (time_now - last_activity_ > READ_TIMEOUT_MS) {
             LOG_ERROR(F("Sensor read timeout"));
-
             state_ = State::IDLE;
-            last_activity_ = time_now;
         }
     } else if (state_ == State::SCANNING) {
         if (time_now - last_activity_ > SCAN_TIMEOUT_MS) {
             LOG_ERROR(F("Sensor scan timeout"));
             state_ = State::IDLE;
-            last_activity_ = time_now;
         } else {
             uint8_t addr[ADDR_LEN] = {0};
 
@@ -133,11 +127,15 @@ void Sensors::loop() {
                 }
             } else {
                 bus_.depower();
+                if ((found_.size() >= devices_.size()) || (retrycnt_ > 5)) {
                     devices_  = std::move(found_);
+                    retrycnt_ = 0;
+                } else {
+                    retrycnt_++;
+                }
                 found_.clear();
                 // LOG_DEBUG(F("Found %zu sensor(s). Adding them."), devices_.size()); // uncomment for debug
                 state_ = State::IDLE;
-                last_activity_ = time_now;
             }
         }
     }

src/sensors.h

@@ -90,7 +90,7 @@ class Sensors {
     static constexpr uint32_t READ_INTERVAL_MS = 5000;  // 5 seconds
     static constexpr uint32_t CONVERSION_MS    = 1000;  // 1 seconds
     static constexpr uint32_t READ_TIMEOUT_MS  = 2000;  // 2 seconds
-    static constexpr uint32_t SCAN_TIMEOUT_MS  = 30000; // 30 seconds
+    static constexpr uint32_t SCAN_TIMEOUT_MS  = 3000;  // 3 seconds
 
     static constexpr uint8_t CMD_CONVERT_TEMP    = 0x44;
     static constexpr uint8_t CMD_READ_SCRATCHPAD = 0xBE;
@@ -111,6 +111,8 @@ class Sensors {
     std::vector<Device> devices_;
 
     uint8_t mqtt_format_;
+    uint8_t retrycnt_ = 0;
+
 };
 
 } // namespace emsesp