show recovery app in Version page

pio_local.ini_example

@@ -2,36 +2,46 @@
 
 [common]
 ; custom build flags to use in my_build_flags
-;  -DEMSESP_UART_DEBUG ; debugging UART
-;  -DEMSESP_DEBUG ; enables DEBUG to the log. Will generate a lot of extra traffic on Console and Syslog
-;  -DEMSESP_DEFAULT_BOARD_PROFILE=\"NODEMCU\" ; hard code the default board name
-;  -DEMSESP_DEBUG_SENSOR ; additional debug for the sensors
-;  -DCORE_DEBUG_LEVEL=5 ; verbose core level debugging 5=verbose, 4=debug, 3=info
-;  -DEMSESP_TEST ; enable the tests. EN language only
-;  -DEMSESP_DE_ONLY ; only DE translated entity names
-;  -DEMSESP_EN_ONLY ; only EN translated entity names
-;  -DEMSESP_PINGTEST ; send log message every 1/2 second
+;  -D EMSESP_UART_DEBUG ; debugging UART
+;  -D EMSESP_DEBUG ; enables DEBUG to the log. Will generate a lot of extra traffic on Console and Syslog
+;  -D EMSESP_DEFAULT_BOARD_PROFILE=\"NODEMCU\" ; hard code the default board name
+;  -D EMSESP_DEBUG_SENSOR ; additional debug for the sensors
+;  -D CORE_DEBUG_LEVEL=5 ; verbose core level debugging 5=verbose, 4=debug, 3=info
+;  -D EMSESP_TEST ; enable the tests. EN language only
+;  -D EMSESP_DE_ONLY ; only DE translated entity names
+;  -D EMSESP_EN_ONLY ; only EN translated entity names
+;  -D EMSESP_PINGTEST ; send log message every 1/2 second
+;  -D EMSESP_GATEWAY_TX_HOLD ; hold Tx while a K30RF/KM200 gateway is syncing, see issue #3094
+;  -D EMSESP_TX_PRE_DELAY=1000 ; wait this many us before each Tx so we don't overlap the master's break, see issue #3094
 
 ; my_build_flags = -DEMSESP_TEST -DEMSESP_DEBUG
 ; my_build_flags = -DEMSESP_DEBUG -DEMSESP_TEST -DEMSESP_PINGTEST
 ; my_build_flags = -DEMSESP_DEBUG -DCORE_DEBUG_LEVEL=5
 ; my_build_flags = -DEMSESP_EN_ONLY -DEMSESP_TEST -DCORE_DEBUG_LEVEL=5 -DARDUINO_USB_CDC_ON_BOOT=1
-my_build_flags =
+; my_build_flags = -DEMSESP_EN_ONLY
+; my_build_flags = -D EMSESP_GATEWAY_TX_HOLD -D EMSESP_TX_PRE_DELAY=1000
+my_build_flags = -DEMSESP_DEBUG
+; my_build_flags = 
 
 [platformio]
-default_envs = s_16M_P ; BBQKees E32V2
-; default_envs = build-webUI ; build the web interface only
-; default_envs = s3_16M_P ; BBQKees S3
-; default_envs = s_4M ; BBQKees older S32, 4MB no psram
-; default_envs = s_16M ; BBQKees newer S32 V2, 16MB no psram
-; default_envs = c6 ; XIAO ESP32C
-; default_envs = debug
+default_envs = s_16M_P, recovery_s_16M_P, build-recovery, build-webUI
+; default_envs = s_16M_P ; BBQKees E32V2
+; default_envs = s_16M_P_custom ; BBQKees E32V2 with custom Arduino/IDF libs
+; default_envs = recovery_s_16M_P ; recovery firmware
+; default_envs = crashtest_s_16M_P ; crash test
+; default_envs = build-webUI ; build the main ems-esp webUI only
+; default_envs = build-recovery ; build the recovery WebUI only
+; default_envs = s3_16M_P ; BBQKees S3 firmware
+; default_envs = s_4M ; firmware forBBQKees older S32, 4MB no psram
+; default_envs = s_16M ; firmware for BBQKees newer S32 V2, 16MB no psram
+; default_envs = c6 ; firmware for XIAO ESP32C
+; default_envs = debug ; see below
 
 [env]
 
+; uncomment if you want to upload the firmware via OTA (must have upload_protocol = custom)
 extra_scripts =
- pre:scripts/build_interface.py ; builds the WebUI
- scripts/rename_fw.py ; renames the firmware .bin file - comment out if not needed
+ post:scripts/rename_fw.py ; renames the firmware .bin file
  scripts/upload.py ; optionally upload the firmware via OTA (must have upload_protocol = custom)
 
 ; set the username and password for the admin account (default password is admin)
@@ -40,13 +50,33 @@ custom_password = admin
 
 ; ** upload settings **
 ; for direct USB, which is the default you can set an optional port for example:
-;  upload_port = /dev/ttyUSB0 or COM3
-;  upload_speed = 921600
+; upload_port = /dev/ttyUSB0
+; upload_port = /dev/ttyACM0
+
+; CH340G bridge tops out here reliably; drop back to 460800 if uploads fail
+; 2000000 is the max speed for the CH340G bridge
+upload_speed = 921600
 
 ; for direct via HTTP (OTA) set:
 ;  upload_protocol = custom
 ;  custom_emsesp_ip = <ip address> or ems-esp.local
 
+upload_protocol = custom
+
+custom_emsesp_ip = ems-esp.local ; E32V2.2 (test)
+; custom_emsesp_ip = ems-espP.local ; E32V2.2 (prod)
+; custom_emsesp_ip = ems-esps32.local ; S32, 4MB no psramS32
+; custom_emsesp_ip = ems-espS3.local ; ems-espS3
+
+; lib_deps =
+;   bblanchon/ArduinoJson @ 7.4.3
+;   ESP32Async/AsyncTCP @ 3.4.10
+;   ESP32Async/ESPAsyncWebServer @ 3.11.0
+;   https://github.com/mobizt/ReadyMail.git @ 0.4.0
+;   https://github.com/mobizt/ESP_SSLClient.git @ 3.1.3
+  ; https://github.com/emsesp/EMS-ESP-Modules.git @ 1.0.8
+;   ; file://${PROJECT_DIR}/../modules/EMS-ESP-Modules
+
 ; ** debug settings **
 ; to be used with an ESP32-S3 which has an onboard JTAG, connect the OTG USB port to the PC
 ; if using an external JTAG board like the ESP-PROG set debug_tool = esp-prog, and use zadig to set the correct driver for the USB port
@@ -69,4 +99,3 @@ debug_init_break =
 upload_speed = 2000000
 monitor_speed = 115200
 extra_scripts =
-; debug_build_flags = -Og -g2 -ggdb2